首页资源分类嵌入式处理器MSP430 > CC1100寄存器配置

CC1100寄存器配置

已有 445117个资源

下载专区

上传者其他资源

    文档信息举报收藏

    标    签:CC1100寄存器配置

    分    享:

    文档简介

    为你使用MSP430单片机配置所需的寄存器

    文档预览

     INT8U FSCTRL2; //自已加的 INT8U FSCTRL1; // Frequency synthesizer control. INT8U FSCTRL0; // Frequency synthesizer control. INT8U FREQ2; // Frequency control word, high INT8U. INT8U FREQ1; // Frequency control word, middle INT8U. INT8U FREQ0; // Frequency control word, low INT8U. INT8U MDMCFG4; // Modem configuration. INT8U MDMCFG3; // Modem configuration. INT8U MDMCFG2; // Modem configuration. INT8U MDMCFG1; // Modem configuration. INT8U MDMCFG0; // Modem configuration. INT8U CHANNR; // Channel number. INT8U DEVIATN; // Modem deviation setting (when FSK modulation is enabled). INT8U FREND1; // Front end RX configuration. INT8U FREND0; // Front end RX configuration. INT8U MCSM0; // Main Radio Control State Machine configuration. INT8U FOCCFG; // Frequency Offset Compensation Configuration. INT8U BSCFG; // Bit synchronization Configuration. INT8U AGCCTRL2; // AGC control. INT8U AGCCTRL1; // AGC control. INT8U AGCCTRL0; // AGC control. INT8U FSCAL3; // Frequency synthesizer calibration. INT8U FSCAL2; // Frequency synthesizer calibration. INT8U FSCAL1; // Frequency synthesizer calibration. INT8U FSCAL0; // Frequency synthesizer calibration. 0x00, 0x08, // FSCTRL1 Frequency synthesizer control. 频率合成器控制 0x00, // FSCTRL0 Frequency synthesizer control. 频率合成器控制 0x10, // FREQ2 Frequency control word, high byte. //频率控制词汇,高字节 0xA7, // FREQ1 Frequency control word, middle byte.//频率控制词汇,中间字节 0x62, // FREQ0 Frequency control word, low byte. //频率控制词汇,低字节 0x5B, // MDMCFG4 Modem configuration. 调制器配置 0xF8, // MDMCFG3 Modem configuration. 调制器配置 0x03, // MDMCFG2 Modem configuration. 调制器配置 0x22, // MDMCFG1 Modem configuration. 调制器配置 0xF8, // MDMCFG0 Modem configuration. 调制器配置 0x00, // CHANNR Channel number. 信道数 0x47, // DEVIATN Modem deviation setting (when FSK modulation is enabled). // 调制解调器偏差设置(FSK调制时启用)。 0xB6, // FREND1 Front end RX configuration. //前末端RX配置。 0x10, // FREND0 Front end RX configuration. // 0x18, // MCSM0 Main Radio Control State Machine configuration.//主要无线电控制状态机的配置。 0x1D, // FOCCFG/ Frequency Offset Compensation Configuration. //频偏补偿配置 0x1C, // BSCFG Bit synchronization Configuration. //位同步配置。 0xC7, // AGCCTRL2 AGC control. AGC控制。 0x00, // AGCCTRL1 AGC control. AGC控制。 0xB2, // AGCCTRL0 AGC control. AGC控制。 0xEA, // FSCAL3 Frequency synthesizer calibration.频率合成器校准 0x2A, // FSCAL2 Frequency synthesizer calibration.频率合成器校准 0x00, // FSCAL1 Frequency synthesizer calibration.频率合成器校准 0x11, // FSCAL0 Frequency synthesizer calibration.频率合成器校准 INT8U FSTEST; // Frequency synthesizer calibration control INT8U TEST2; // Various test settings. INT8U TEST1; // Various test settings. INT8U TEST0; // Various test settings. INT8U IOCFG2; // GDO2 output pin configuration INT8U IOCFG0; // GDO0 output pin configuration INT8U PKTCTRL1; // Packet automation control. INT8U PKTCTRL0; // Packet automation control. INT8U ADDR; // Device address. INT8U PKTLEN; // Packet length. 0x59, // FSTEST Frequency synthesizer calibration.频率合成器校准 0x81, // TEST2 Various test settings.不同的测试设置 0x35, // TEST1 Various test settings.不同的测试设置 0x09, // TEST0 Various test settings.不同的测试设置 0x0B, // IOCFG2 GDO2 output pin configuration. GDO2输出引脚配置。 0x06, // IOCFG0D GDO0 output pin configuration. Refer to SmartRF?Studio User Manual for detailed pseudo register explanation. //GDO0输出引脚配置。参照SmartRF?Studio用户手册详细解释伪寄存器。 0x04, // PKTCTRL1 Packet automation control. 数据包自动化控制。 0x05, // PKTCTRL0 Packet automation control. 数据包自动化控制。 0x00, // ADDR Device address. 设备地址。 0x0c // PKTLEN Packet length. 包长度

    Top_arrow
    回到顶部
    EEWORLD下载中心所有资源均来自网友分享,如有侵权,请发送举报邮件到客服邮箱bbs_service@eeworld.com.cn 或通过站内短信息或QQ:273568022联系管理员 高进,我们会尽快处理。