datasheet
超过460,000+ 应用技术资源下载
pdf

SPX1117_en.pdf

  • 1星
  • 日期: 2014-06-13
  • 大小: 459.85KB
  • 所需积分:1分
  • 下载次数:0
  • favicon收藏
  • rep举报
  • 分享
  • free评论
标签: SPX1117_en

SPX1117_en.pdf

SPX1117 800mA Low Dropout Voltage Regulator FEATURES ■ Guaranteed 0.8A Output Current ■ Guaranteed 1A Peak Current ■ Three Terminal Adjustable or Fixed 1.5V, 1.8V, 2.5V, 2.85V, 3.0V, 3.3V and 5V ■ Low Quiescent Current ■ Low Dropout Voltage of 1.1V at 0.8A ■ 0.1% Line and 0.2% Load Regulation ■ Stable with 2.2uF Ceramic Capacitor ■ Overcurrent and Thermal Protection ■ Lead Free, RoHS Compliant Packages: SOT-223,TO-252, TO-220, and TO-263 APPLICATIONS ■ Desktop PC's Servers ■ SCSI-II Active Terminator ■ Portable/ Palm Top / Notebook Computers ■ Cordless Phones ■ Battery Chargers ■ Disk Drives ■ Portable Consumer Equipment ■ Portable Instrumentation ■ SMPS Post-Regulator DESCRIPTION The SPX1117 is a low power positive-voltage regulator designed to satisfy moderate power requirements with a cost effective, small footprint solution. This device is an excellent choice for use in battery-powered applications and portable computers. The SPX1117 features very low quiescent current and a low dropout voltage of 1.1V at a full load. As output current decreases, quiescent current flows into the load, increasing efficiency. SPX1117 is available in adjustable or fixed 1.5V, 1.8V, 2.5V,2.5V, 2.85V, 3.0V, 3.3V and 5V output voltages. The SPX1117 is offered in several 3-pin surface mount packages: SOT-223, TO-252, TO-220 and TO-263. An output capacitor of 10µF provides unconditional stability while a smaller 2.2µF capacitor is sufficient for most applications. FUNCTIONAL DIAGRAM VIN Apr 20-07 Rev B Current Limit Thermal Limit I TL + - ICL + – + AMP - 1.25V VOUT VREF ADJ/GND IADJ ~ 50µA – SPX1117 800mA Low Dropout Voltage Regulator 1 © 2007 Sipex Corporation Power Dissipation.......................................Internally Limited Lead Temperature (soldering, 5 seconds) ...............260°C Storage Temperature Range.......................-65°C to +150°C Operating Junction Temperature Range.....-40°C to +125°C Input Supply Voltage .................................................... +20V Input to Output Voltage ................................................ 18.8V ESD Rating.................................................................2kV min ABSOLUTE MAXIMUM RATINGS These are sterss ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. ELECTRICAL CHARACTERISTICS TA = 25°C, CIN = COUT = 10µF, unless otherwise specified. The Boldface applies over the full operating temperature range. PARAMETER 1.5V Version Output Voltage 1.8V Version Output Voltage 2.5V Version Output Voltage 2.85V Version Output Voltage 3.00V Version Output Voltage 3.30V Version Output Voltage 5V Version Output Voltage All Voltage Options Reference Voltage Output Voltage Temperature Stability Line Regulation (Note 1) CONDITIONS MIN IOUT = 5mA, VIN =3.0V, TJ = 25ºC 5mA ≤ IOUT ≤ 800mA, 2.9V ≤ VIN ≤ 10V 1.485 1.470 IOUT = 5mA, VIN =3.3V, TJ = 25ºC 5mA ≤ IOUT ≤ 800mA, 3.2V ≤ VIN ≤ 10V 1.782 1.764 IOUT = 5mA, VIN =4.0V, TJ = 25ºC 5mA ≤ IOUT ≤ 800mA, 3.9V ≤ VIN ≤ 10V 2.475 2.450 IOUT = 5mA, VIN =4.35V, TJ = 25ºC 5mA ≤ IOUT ≤ 800mA, 4.25V ≤ VIN ≤ 10V 2.821 2.793 IOUT = 5mA, VIN =4.5V, TJ = 25ºC 5mA ≤ IOUT ≤ 800mA, 4.4V ≤ VIN ≤ 10V 2.970 2.940 IOUT = 5mA, VIN =4.8V, TJ = 25ºC 5mA ≤ IOUT ≤ 800mA, 4.7V ≤ VIN ≤ 10V 3.267 3.234 IOUT = 5mA, VIN =6.5V 5mA ≤ IOUT ≤ 800mA, 6.4V ≤ VIN ≤ 12V 4.950 4.90 IOUT=5mA, (VIN - VOUT )= 2V, TJ = 25ºC 5mA≤IOUT≤ 800mA, 1.4V≤(VIN-VOUT)≤ 10V 1.238 1.225 VINMIN ≤VIN≤ 12V,VOUT=Fixed/Adj, IOUT=5mA TYP 1.500 1.800 2.500 2.850 3.000 3.300 5 1.250 0.3 3 MAX UNITS 1.515 V 1.530 1.818 V 1.836 2.525 V 2.550 2.878 V 2.907 3.030 V 3.060 3.333 V 3.366 5.050 V 5.10 1.262 V 1.270 % 7 mV Load Regulation (Note 1) Dropout Voltage (Note 2) Quiescent Current 5mA≤IOUT≤ 800mA,VOUT=Fixed/Adj IOUT=100mA I =500mA OUT IOUT=800mA 4.25V≤VIN≤ 6.5V 6 12 mV 1.00 1.20 V 1.05 1.25 1.10 1.30 5 10 mA Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 2 © 2007 Sipex Corporation ELECTRICAL CHARACTERISTICS TA = 25°C, CIN = COUT = 10µF, unless otherwise specified. The Boldface applies over the full operating temperature range. PARAMETER Adjust Pin Current Current Limit Thermal Regulation CONDITIONS (VIN-VOUT)=5V 25°C, 30mS pulse MIN TYP MAX UNITS 50 120 µA 1.0 1.5 2.0 A 0.01 0.1 %/W Ripple Rejection fRIPPLE=120Hz, (VIN-VOUT)=2V, 60 75 dB VRIPPLE=1VPP Long Term Stability 125°C, 1000Hrs 0.03 % RMS Output Noise % of VOUT, 10Hz≤f≤10kHz 0.003 % *Note 1 - For fixed option, VINMIN = VOUT + 1.5V - For adjustable option, V = V - V = 1.4V INMIN IN OUT *Note 2 - Dropout voltage is the input voltage minus output voltage that produces a 1% decrease in output voltage with respect to the nominal output voltage at VIN = VOUT + 1.5V Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 3 © 2007 Sipex Corporation TYPICAL PERFORMANCE CHARACTERISTICS Output Voltage 3.320 3.315 3.310 3.305 3.300 3.295 3.290 3.285 3.280 10 100 Output Current (mA) 1000 Figure 1. Load Regulation for SPX1117M3-3.3; VIN=4.8V Dropout Voltage (V) 1.3 1.2 1.1 1.0 0.9 100 200 300 400 500 600 700 800 900 1000 Io (mA) Figure 3. Dropout Voltage vs Output Current for SPX1117M3-3.3; VIN=4.8V, COUT=2.2µF Vout (V) 3.325 3.320 3.315 3.310 3.305 3.300 4.5 6.5 8.5 10.5 12.5 14.5 Vin (V) Figure 2. Line Regulation for SPX1117M3-3.3; IOUT=10mA 2.00 Current Limit (A) 1.50 1.00 0.50 0.00 -50 -25 0 25 50 75 100 125 Temp (oC) Figure 4. Current Limit for SP1117M3-3.3; VIN=4.8V, CIN=COUT=1µF, IOUT pulsed from 10mA to Current Limit Output Deviation (mV) 100 125°C 22µF 0 -100 1.5 1.0 0.5 0 Indicating Current Limit Starts VIN = 4.0V VIN=3.3V Fixed 1O=10mA CIN=1µF Tan Cap COUT=2.2µF Tan Cap Output Current (A) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Time (ms) Figure 5. Current Limit for SPX1117M3-3.3, Output Voltage Deviation with IOUT=10mA to 1A Step Vout (V) 1.275 1.27 1.265 1.25v Adj 1.26 1.255 1.25 1.245 1.24 1.235 1.23 1.225 -50 -30 -10 10 30 50 70 90 110 130 Temp (C) Figure 6. VOUT vs Temperature, VIN=2.5V, IOUT=10mA Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 4 © 2007 Sipex Corporation TYPICAL PERFORMANCE CHARACTERISTICS: Continued 1.53 1.52 1.5v Adj 1.5v Fixed 1.51 Vout (V) 1.5 1.49 1.48 1.47 -50 -30 -10 10 30 50 70 90 110 130 Temp (C) Figure 7. VIN=3.0V, IOUT=10mA Vout (V) 1.84 1.83 1.8v Adj 1.82 1.8v Fixed 1.81 1.8 1.79 1.78 1.77 1.76 -50 -30 -10 10 30 50 70 90 110 130 Temp (C) Figure 8. VIN=3.3V, IOUT=10mA 2.55 2.54 2.5v Adj 2.53 2.52 2.5v Fixed 2.51 2.5 2.49 2.48 2.47 2.46 2.45 -50 -30 -10 10 30 50 70 90 110 130 Temp (C) Figure 9. VIN=4.0V, IOUT=10mA Vout (V) 2.92 2.9 2.88 2.86 2.84 2.82 2.8 -50 -30 -10 10 30 50 70 Temp (C) Figure 10. VIN=4.85V, IOUT=10mA 2.85v Adj 2.85v Fixed 90 110 130 Vout (V) Vout (V) 3.06 3.04 3.02 3 2.98 2.96 2.94 -50 -30 -10 10 30 50 70 Temp (C) Figure 11. VIN=4.85V, IOUT=10mA 3v Adj 3v Fixed 90 110 130 Output Voltage Change, mV 6 4 2 0 -2 -4 -6 -8 -40 -20 0 20 40 60 Ambient Temperature,*C 80 100 Figure 13. Line Regulation vs Temperature. VOUT=1.8V (adjustable), VIN= 3.3V Vout tolerance,% 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 3 4 5 Vin, V -40°C +25°C +85°C 6 Figure 15. Line Regulation at ILOAD=800mA over Temperature, VOUT=1.8V adjustable 3.38 3.36 3.3v Adj 3.3v Fixed 3.34 Vout (V) 3.32 3.3 3.28 3.26 -50 -30 -10 10 30 50 70 90 110 130 Temp (C) Figure 12. VIN=5.0V, IOUT=10mA V out, V 1.816 1.815 1.814 1.813 1.812 1.811 1.81 1.809 1.808 1.807 1.806 -40 -20 800mA 400mA 10mA 0 20 40 60 Ambient Temperature, *C 80 100 Figure 14. Output Voltage vs Temperature at different Current Loads, VIN=3.3V, VOUT = 1.8V Adjustable Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 5 © 2007 Sipex Corporation Output Capacitor To ensure the stability of the SPX1117, an output capacitor of at least 2.2µF (tantalum or ceramic) or 10µF (aluminum) is required. The value may change based on the application requirements of the output load or temperature range. The value of ESR can vary based on the type of capacitor used in the applications to guarantee stability. The recommended value for ESR is 0.5Ω or less. A larger value of output capacitance (up to 100µF) can improve the load transient response. APPLICATION INFORMATION Figure 16. Load Step Response (0 to 800mA), Vin=3.3V, Vout=1.8V, Cin=10µF, Cout=2.2µF, Ceramic; 1 = Vout, 4= Iload Soldering Methods The SPX1117 SOT-223 package is designed to be compatible with infrared reflow or vapor-phase reflow soldering techniques. During soldering, the non-active or mildly active fluxes may be used. The SPX1117 die is attached to the heatsink lead which exits opposite the input, output, and ground pins. Hand soldering and wave soldering should be avoided since these methods can cause damage to the device with excessive thermal gradients on the package. The SOT-223 recommended soldering method are as follows: vapor phase reflow and infrared reflow with the component preheated to within 65°C of the soldering temperature range. Figure 17. Load Step Response (0 to 800mA), Vin=3.3V, Vout=1.8V, Cin=10µF, Cout=2.2µF, OSCON; 1 = Vout, 4= Iload Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 6 © 2007 Sipex Corporation Thermal Characteristics The thermal resistance of SPX1117 (SOT-223 Package) is 15°C/W from junction to tab and 31 °C/W from tab to ambient for a total of 46 °C/W from junction to ambient (Table 1). The SPX1117 features the internal thermal limiting to protect the device during overload conditions. Special care needs to be taken during continuous load conditions such that the maximum junction temperature does not exceed 125 °C. Thermal protection is activated at >155°C and deactiviated at <140 °C. Taking the FR-4 printed circuit board and 1/16 thick with 1 ounce copper foil as an experiment (fig.13), the PCB material is effective at transmitting heat with the tab attached to the pad area and a ground plane layer on the backside of the substrate. Refer to table 1 for the results of the experiment. The thermal interaction from other components in the application can effect the thermal resistance of the SPX1117. The actual thermal resistance can be determined with experimentation. SPX1117 power dissipation is calculated as follows: PD = (VIN - VOUT)(IOUT) Maximum Junction Temperature range: TJ = TA(max) + PD* thermal resistance (junction-to-ambient) Maximum junction temperature must not exceed the 125°C. APPLICATION INFORMATION: Continued Ripple Rejection Ripple rejection can be improved by adding a capacitor between the ADJ pin and ground as shown in Figure 23. When ADJ pin bypassing is used, the value of the output capacitor required increases to its maximum. If the ADJ pin is not bypassed, the value of the output capacitor can be lowered to 10µF for an electrolytic aluminum capacitor or 2.2µF for a ceramic or solid tantalum capacitor (Fig 22). However the value of the ADJ-bypass capacitor should be chosen with respect to the following equation: C = 1 / ( 6.28 * F * R ) R 1 Where C = value of the capacitor in Farads (select an equal or larger standard value), FR = ripple frequency in Hz, R = value of resistor R1 in Ohms. 1 If an ADJ-bypass capacitor is used, the amplitude of the output ripple will be independent of the output voltage. If an ADJ-bypass capacitor is not used, the output ripple will be proportional to the ratio of the output voltage to the reference voltage: M = VOUT / VREF Where M = multiplier for the ripple seen when the ADJ pin is optimally bypassed. VREF =1.25V Ripple rejection for the adjustable version is shown in Figure 20. 50 X 50mm 35 X 17mm 16 X 10mm Ripple Rejection, Db 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 10 100 1000 10000 100000 1000000 Frequency, Hz Figure 19. Substrate Layout for SOT-223 Figure 20. Ripple Rejection; Vin=3.3V, Vout=1.8V (adj.), Iload=200mA Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 7 © 2007 Sipex Corporation TABLE 1 PC BOARD mm2 2500 2500 2500 2500 2500 1600 2500 2500 1600 900 900 APPLICATION INFORMATION: Continued TOPSIDE COPPER BACKSIDE COPPER mm2 2500 1250 950 2500 1800 600 1250 915 600 240 240 mm2 2500 2500 2500 0 0 1600 0 0 0 900 0 THERMAL RESISTANCE JUNC. TO AMB. °C/W 46 47 49 51 53 55 58 59 67 72 85 Output Voltage The output of the adjustable regulator can be set to any voltage between 1.25V and 15V. The value of V can be quickly approximated using OUT the formula VOUT=1.25 *(R1 + R2)/R1. A small correction to this formula is required depending on the values of resistors R and R , 1 2 since the adjustable pin current (approx 50µA) flows through R2. When IADJ is taken into account, the formula becomes VOUT = VREF(1+ (R2/R1)) + IADJ * R2, where V =1.25V. REF Layout Considerations Parasitic line resistance can degrade load regulation. In order to avoid this, connect R directly 1 to V as illustrated in Figure 25. For the same OUT reason, R should be connected to the negative 2 side of the load. V IN IN 4.7µF + C 1 SPX1117 ADJ IOUT = VREF R1 OUT VOUT C2 R1 IOUT LOAD VIN IN 4.7µF + C1 SPX1117 ADJ I ADJ 50µA VOUT = V REF (1+R 2 /R1) +IADJ R 2 OUT VREF R1 VOUT C2 R2 Figure 21. Current Source Figure 22. Typical Adjustable Regulator Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 8 © 2007 Sipex Corporation APPLICATION INFORMATION: Continued (Note A) V IN + 4.7µF SPX1117 5V IN OUT V OUT ADJ R1 330Ω 1% *C 1 improves ripple rejection. ZC should be ~ R1 at ripple frequency R2 1kΩ, 1% 10µF + C1 10µF* Note A: VIN(MIN) = (Intended VOUT ) + (V DROPOUT (MAX)) Figure 23. Improving Ripple Rejection VIN (Note A) + SPX1117 IN OUT ADJ 4.7µF 1K TTL Input 2N3904 1k 5V 330W 1% + 10µF 1kΩ 1% Note A: V = (Intended V ) + (V ) IN(MIN) OUT DROPOUT (MAX) Figure 24. 5V Regulator with Shutdown RP Parasitic Line Resistance VIN SPX1117 VOUT ADJ Connect R to Case of Regulator R 1 R2 Connect R2 to Load RL Figure 25. Recommended Connections for Best Results SOT-223 (M3) TO-252 (R) TO-220-3 (U) TO-263-3 (T) PINOUTS 1 23 ADJ/GND V OUT V IN Top View 1 23 ADJ/GND V OUT V IN 123 Front View ADJ/GND V OUT V IN Front View Note: For all Pinouts, TAB is connected to Pin2 VOUT. 123 ADJ/GND V OUT V IN Top View Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 9 © 2007 Sipex Corporation PACKAGE: 3 PIN SOT-223 Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 10 © 2007 Sipex Corporation PACKAGE: 3 PIN TO-252 Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 11 © 2007 Sipex Corporation PACKAGE: 3 PIN TO-220 Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 12 © 2007 Sipex Corporation PACKAGE: 3 PIN TO-263 Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 13 © 2007 Sipex Corporation Ordering Information Part Number Status RoHS Package Pack Type Quantity SPX1117HM3/TR Active No SOT-223-3 Tape & Reel 2500 SPX1117HM3-L/TR Active Yes SOT-223-3 Tape & Reel 2500 SPX1117HM3-L-1-8/TR Active Yes SOT-223-3 Tape & Reel 2500 SPX1117M3 Active No SOT-223-3 TUBE 78 SPX1117M3/TR Active No SOT-223-3 Tape & Reel 2500 SPX1117M3-1-5/TR Active No SOT-223-3 Tape & Reel 2500 SPX1117M3-1-8/TR Active No SOT-223-3 Tape & Reel 2500 SPX1117M3-2-5/TR Active No SOT-223-3 Tape & Reel 2500 SPX1117M3-2-85 Active No SOT-223-3 TUBE 78 SPX1117M3-3-0/TR Active No SOT-223-3 Tape & Reel 2500 SPX1117M3-3-3/TR Active No SOT-223-3 Tape & Reel 2500 SPX1117M3-5-0/TR Active No SOT-223-3 Tape & Reel 2500 SPX1117M3-L Active Yes SOT-223-3 TUBE 78 SPX1117M3-L/TR Active Yes SOT-223-3 Tape & Reel 2500 SPX1117M3-L-1-5 Active Yes SOT-223-3 TUBE 78 SPX1117M3-L-1-5/TR Active No SOT-223-3 Tape & Reel 2500 SPX1117M3-L-1-8/TR Active Yes SOT-223-3 Tape & Reel 2500 SPX1117M3-L-2-5/TR Active Yes SOT-223-3 Tape & Reel 2500 SPX1117M3-L-2-85/TR Active Yes SOT-223-3 Tape & Reel 2500 SPX1117M3-L-3-0 Active Yes SOT-223-3 TUBE 78 SPX1117M3-L-3-0/TR Active Yes SOT-223-3 Tape & Reel 2500 SPX1117M3-L-3-3/TR Active Yes SOT-223-3 Tape & Reel 2500 SPX1117M3-L-5-0/TR Active Yes SOT-223-3 Tape & Reel 2500 SPX1117R Active No TO-252-3 TUBE 77 SPX1117R/TR Active No TO-252-3 Tape & Reel 2000 SPX1117R-1-5 Active No TO-252-3 TUBE 77 SPX1117R-1-5/TR Active No TO-252-3 Tape & Reel 2000 SPX1117R-1-8 Active No TO-252-3 TUBE 77 SPX1117R-1-8/TR Active No TO-252-3 Tape & Reel 2000 SPX1117R-2-5 Active No TO-252-3 TUBE 77 SPX1117R-2-5/TR Active No TO-252-3 Tape & Reel 2000 SPX1117R-2-85 Active No TO-252-3 TUBE 77 SPX1117R-2-85/TR Active No TO-252-3 Tape & Reel 2000 SPX1117R-3-0 Active No TO-252-3 TUBE 77 SPX1117R-3-0/TR Active No TO-252-3 Tape & Reel 2000 SPX1117R-3-3 Active No TO-252-3 TUBE 77 SPX1117R-3-3/TR Active No TO-252-3 Tape & Reel 2000 SPX1117R-L Active Yes TO-252-3 TUBE 77 SPX1117R-L/TR Active Yes TO-252-3 Tape & Reel 2000 SPX1117R-L-1-5 Active Yes TO-252-3 TUBE 77 SPX1117R-L-1-5/TR Active Yes TO-252-3 Tape & Reel 2000 SPX1117R-L-1-8 Active Yes TO-252-3 TUBE 77 SPX1117R-L-1-8/TR Active Yes TO-252-3 Tape & Reel 2000 SPX1117R-L-2-5 Active Yes TO-252-3 TUBE 77 SPX1117R-L-2-5/TR Active Yes TO-252-3 Tape & Reel 2000 SPX1117R-L-2-85 Active Yes TO-252-3 TUBE 77 SPX1117R-L-2-85/TR Active Yes TO-252-3 Tape & Reel 2000 SPX1117R-L-3-0 Active Yes TO-252-3 TUBE 77 SPX1117R-L-3-0/TR Active Yes TO-252-3 Tape & Reel 2000 SPX1117R-L-3-3 Active Yes TO-252-3 TUBE 77 SPX1117R-L-3-3/TR Active Yes TO-252-3 Tape & Reel 2000 Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 14 © 2007 Sipex Corporation Ordering Information Part Number SPX1117T SPX1117T/TR SPX1117T-1-5 SPX1117T-1-5/TR SPX1117T-1-8 SPX1117T-1-8/TR SPX1117T-2-5 SPX1117T-2-5/TR SPX1117T-2-85 SPX1117T-3-0 SPX1117T-3-0/TR SPX1117T-3-3 SPX1117T-3-3/TR SPX1117T-L SPX1117T-L/TR SPX1117T-L-1-5 SPX1117T-L-1-5/TR SPX1117T-L-1-8 SPX1117T-L-1-8/TR SPX1117T-L-2-5 SPX1117T-L-2-5/TR SPX1117T-L-2-85 SPX1117T-L-2-85/TR SPX1117T-L-3-0 SPX1117T-L-3-0/TR SPX1117T-L-3-3 SPX1117T-L-3-3/TR SPX1117U SPX1117U-1-5 SPX1117U-1-8 SPX1117U-2-5 SPX1117U-2-85 SPX1117U-3-0 SPX1117U-3-3 SPX1117U-L SPX1117U-L-1-5 SPX1117U-L-1-8 SPX1117U-L-2-5 SPX1117U-L-2-8-5 SPX1117U-L-3-0 SPX1117U-L-3-3 SPX1117HM3 Status RoHS Package Pack Type Quantity Active No TO-263-3 TUBE 50 Active No TO-263-3 Tape & Reel 500 Active No TO-263-3 TUBE 50 Active No TO-263-3 Tape & Reel 500 Active No TO-263-3 TUBE 50 Active No TO-263-3 Tape & Reel 500 Active No TO-263-3 TUBE 50 Active No TO-263-3 Tape & Reel 500 Active No TO-263-3 TUBE 50 Active No TO-263-3 TUBE 50 Active No TO-263-3 Tape & Reel 500 Active No TO-263-3 TUBE 50 Active No TO-263-3 Tape & Reel 500 Active Yes TO-263-3 TUBE 50 Active Yes TO-263-3 Tape & Reel 500 Active Yes TO-263-3 TUBE 50 Active Yes TO-263-3 Tape & Reel 500 Active Yes TO-263-3 TUBE 50 Active Yes TO-263-3 Tape & Reel 500 Active Yes TO-263-3 TUBE 50 Active Yes TO-263-3 Tape & Reel 500 Active Yes TO-263-3 TUBE 50 Active Yes TO-263-3 Tape & Reel 50 Active Yes TO-263-3 TUBE 50 Active Yes TO-263-3 Tape & Reel 500 Active Yes TO-263-3 TUBE 50 Active Yes TO-263-3 Tape & Reel 500 Active No TO-220-3 TUBE 50 Active No TO-220-3 TUBE 50 Active No TO-220-3 TUBE 50 Active No TO-220-3 TUBE 50 Active No TO-220-3 TUBE 50 Active No TO-220-3 TUBE 50 Active No TO-220-3 TUBE 50 Active Yes TO-220-3 TUBE 50 Active Yes TO-220-3 TUBE 50 Active Yes TO-220-3 TUBE 50 Active Yes TO-220-3 TUBE 50 Active Yes TO-220-3 TUBE 50 Active Yes TO-220-3 TUBE 50 Active Yes TO-220-3 TUBE 50 CF No SOT-223-3 TUBE 78 Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 15 © 2007 Sipex Corporation Ordering Information Part Number Status RoHS Package Pack Type Quantity SPX1117HM3-1-5 CF No SOT-223-3 TUBE 78 SPX1117HM3-2-5 CF No SOT-223-3 TUBE 78 SPX1117HM3-3-3 CF No SOT-223-3 TUBE 78 SPX1117HM3-5-0 CF No SOT-223-3 TUBE 78 SPX1117HM3-L CF Yes SOT-223-3 TUBE 78 SPX1117HM3-L-1-5 CF Yes SOT-223-3 TUBE 78 SPX1117HM3-L-1-5/TR CF Yes SOT-223-3 Tape & Reel 2500 SPX1117HM3-L-1-8 CF Yes SOT-223-3 TUBE 78 SPX1117HM3-L-2-5 CF Yes SOT-223-3 TUBE 78 SPX1117HM3-L-2-5/TR CF Yes SOT-223-3 Tape & Reel 2500 SPX1117HM3-L-2-85 CF Yes SOT-223-3 TUBE 78 SPX1117HM3-L-2-85/TR CF Yes SOT-223-3 Tape & Reel 2500 SPX1117HM3-L-3-0 CF Yes SOT-223-3 TUBE 78 SPX1117HM3-L-3-0/TR CF Yes SOT-223-3 Tape & Reel 2500 SPX1117HM3-L-3-3 CF Yes SOT-223-3 TUBE 78 SPX1117HM3-L-3-3/TR CF Yes SOT-223-3 Tape & Reel 2500 SPX1117HM3-L-5-0 CF Yes SOT-223-3 TUBE 78 SPX1117HM3-L-5-0/TR CF Yes SOT-223-3 Tape & Reel 2500 SPX1117M3-1-5 CF_ No SOT-223-3 TUBE 78 SPX1117M3-1-8 CF_ No SOT-223-3 TUBE 78 SPX1117M3-2-5 CF_ No SOT-223-3 TUBE 78 SPX1117M3-3-0 CF_ No SOT-223-3 TUBE 78 SPX1117M3-3-3 CF_ No SOT-223-3 TUBE 78 SPX1117M3-5-0 CF_ No SOT-223-3 TUBE 78 SPX1117M3-L-1-8 CF_ Yes SOT-223-3 TUBE 78 SPX1117M3-L-2-5 CF_ Yes SOT-223-3 TUBE 78 SPX1117M3-L-2-85 CF_ Yes SOT-223-3 TUBE 78 SPX1117M3-L-3-3 CF_ Yes SOT-223-3 TUBE 78 SPX1117M3-L-5-0 CF_ Yes SOT-223-3 TUBE 78 SPX1117HM3-1-5/TR OBS No SOT-223-3 Tape & Reel 2500 SPX1117HM3-1-8 OBS No SOT-223-3 TUBE 78 SPX1117HM3-1-8/TR OBS No SOT-223-3 Tape & Reel 2500 SPX1117HM3-2-5/TR OBS No SOT-223-3 Tape & Reel 2500 SPX1117HM3-2-85 OBS No SOT-223-3 TUBE 78 SPX1117HM3-2-85/TR OBS No SOT-223-3 Tape & Reel 2500 SPX1117HM3-3-0 OBS No SOT-223-3 TUBE 78 SPX1117HM3-3-0/TR OBS No SOT-223-3 Tape & Reel 2500 SPX1117HM3-3-3/TR OBS No SOT-223-3 Tape & Reel 2500 TM SPX1117HM3-5-0/TR OBS No SOT-223-3 Tape & Reel 2500 For further assistance: Email: WWW Support page: Sipex Application Notes: Sipexsupport@sipex.com http://www.sipex.com/content.aspx?p=support http://www.sipex.com/applicationNotes.aspx Solved by Sipex Corporation Headquarters and Sales Office 233 South Hillview Drive Milpitas, CA 95035 tel: (408) 934-7500 fax: (408) 935-7600 Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 16 © 2007 Sipex Corporation
更多简介内容

评论

下载专区


TI最新应用解决方案

工业电子 汽车电子 个人消费电子