首页资源分类电源技术 > at24c64.pdf

at24c64.pdf

已有 453308个资源

下载专区

文档信息举报收藏

标    签: at24c64

分    享:

文档简介

at24c64.pdf

文档预览

Features • Low-Voltage and Standard-Voltage Operation – 5.0 (VCC = 4.5V to 5.5V) – 2.7 (VCC = 2.7V to 5.5V) – 2.5 (VCC = 2.5V to 5.5V) – 1.8 (VCC = 1.8V to 5.5V) • Low-Power Devices (ISB = 2 µA @ 5.5V) Available • Internally Organized 4096 x 8, 8192 x 8 • 2-Wire Serial Interface • Schmitt Trigger, Filtered Inputs for Noise Suppression • Bidirectional Data Transfer Protocol • 100 kHz (1.8V, 2.5V, 2.7V) and 400 kHz (5V) Compatibility • Write Protect Pin for Hardware Data Protection • 32-Byte Page Write Mode (Partial Page Writes Allowed) • Self-Timed Write Cycle (10 ms max) • High Reliability – Endurance: 1 Million Write Cycles – Data Retention: 100 Years – ESD Protection: >3,000V • Automotive Grade and Extended Temperature Devices Available • 8-Pin JEDEC PDIP, 8-Pin and 14-Pin JEDEC SOIC, 8-Pin EIAJ SOIC, and 8-pin TSSOP Packages Description The AT24C32/64 provides 32,768/65,536 bits of serial electrically erasable and programmable read only memory (EEPROM) organized as 4096/8192 words of 8 bits each. The device’s cascadable feature allows up to 8 devices to share a common 2wire bus. The device is optimized for use in many industrial and commercial applications where low power and low voltage operation are essential. The AT24C32/64 is available in space saving 8-pin JEDEC PDIP, 8-pin and 14-pin JEDEC SOIC, 8-pin EIAJ SOIC, and 8-pin TSSOP packages and is accessed via a 2-wire serial interface. In addition, the entire family is available in 5.0V (4.5V to 5.5V), 2.7V (2.7V to 5.5V), 2.5V (2.5V to 5.5V) and 1.8V (1.8V to 5.5V) versions. Pin Configurations Pin Name A0 to A2 SDA Function Address Inputs Serial Data 8-Pin PDIP A0 1 A1 2 A2 3 GND 4 8 VCC 7 WP 6 SCL 5 SDA SCL Serial Clock Input WP Write Protect 14-Pin SOIC 8-Pin TSSOP A0 1 A1 2 A2 3 GND 4 8 VCC 7 WP 6 SCL 5 SDA NC 1 A0 2 A1 3 NC 4 A2 5 GND 6 NC 7 14 NC 13 VCC 12 WP 11 NC 10 SCL 9 SDA 8 NC 8-Pin SOIC A0 1 A1 2 A2 3 GND 4 8 VCC 7 WP 6 SCL 5 SDA 2-Wire Serial EEPROM 32K (4096 x 8) 64K (8192 x 8) AT24C32 AT24C64 2-Wire, 32K Serial E2PROM Rev. 0336F–08/98 1 Absolute Maximum Ratings* Operating Temperature .................................. -55°C to +125°C Storage Temperature ..................................... -65°C to +150°C Voltage on Any Pin with Respect to Ground .....................................-1.0V to +7.0V Maximum Operating Voltage........................................... 6.25V DC Output Current........................................................ 5.0 mA Block Diagram *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open collector devices. DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1 and A0 pins are device address inputs that are hard wired or left not connected for hardware compatibility with AT24C16. When the pins are hardwired, as many as eight 32K/64K devices may be addressed on a single bus system (device addressing is discussed in detail under the Device Addressing section). When the pins are not hardwired, the default A2, A1, and A0 are zero. WRITE PROTECT (WP): The write protect input, when tied to GND, allows normal write operations. When WP is tied high to VCC, all write operations to the upper quandrant (8/16K bits) of memory are inhibited. If left unconnected, WP is internally pulled down to GND. Memory Organization AT24C32/64, 32K/64K SERIAL EEPROM: The 32K/64K is internally organized as 256 pages of 32 bytes each. Random word addressing requires a 12/13 bit data word address. 2 AT24C32/64 AT24C32/64 Pin Capacitance(1) Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +1.8V. Symbol Test Condition Max CI/O Input/Output Capacitance (SDA) 8 CIN Input Capacitance (A0, A1, A2, SCL) 6 Note: 1. This parameter is characterized and is not 100% tested. Units pF pF Conditions VI/O = 0V VIN = 0V DC Characteristics Applicable over recommended operating range from: TAI = -40°C to +85°C, VCC = +1.8V to +5.5V, TAC = 0°C to +70°C, VCC = +1.8V to +5.5V (unless otherwise noted). Symbol Parameter Test Condition Min Typ Max Units VCC1 Supply Voltage 1.8 5.5 V VCC2 Supply Voltage 2.5 5.5 V VCC3 Supply Voltage 2.7 5.5 V VCC4 Supply Voltage 4.5 5.5 V ICC1 Supply Current VCC = 5.0V READ at 100 kHz 0.4 1.0 mA ICC2 Supply Current VCC = 5.0V WRITE at 100 kHz 2.0 3.0 mA ISB1 Standby Current (1.8V option) VCC = 1.8V VCC = 5.5V VIN = VCC or VSS 0.1 µA 2.0 ISB2 Standby Current (2.5V option) VCC = 2.5V VCC = 5.5V VIN = VCC or VSS 0.5 µA 2.0 ISB3 Standby Current (2.7V option) VCC = 2.7V VCC = 5.5V VIN = VCC or VSS 0.5 µA 2.0 ISB4 Standby Current (5V option) VCC = 4.5 - 5.5V VIN = VCC or VSS 20 35 µA ILI ILO VIL VIH VOL2 VOL1 Notes: Input Leakage Current Output Leakage Current Input Low Level(1) VIN = VCC or VSS VOUT = VCC or VSS Input High Level(1) Output Low Level VCC = 3.0V IOL = 2.1 mA Output Low Level VCC = 1.8V IOL = 0.15 mA 1. VIL min and VIH max are reference only and are not tested. -0.6 VCC x 0.7 0.10 3.0 µA 0.05 3.0 µA VCC x 0.3 V VCC + 0.5 V 0.4 V 0.2 V 3 AC Characteristics Applicable over recommended operating range from TA = -40°C to +85°C, VCC = +1.8V to +5.5V, CL = 1 TTL Gate and 100 pF (unless otherwise noted). 1.8-volt 2.7-, 2.5-volt 5.0-volt Symbol Parameter Min Max Min Max Min Max Units fSCL tLOW tHIGH tI tAA tBUF Clock Frequency, SCL 100 100 400 kHz Clock Pulse Width Low 4.7 4.7 1.2 µs Clock Pulse Width High Noise Suppression Time(1) 4.0 4.0 0.6 µs 100 100 50 ns Clock Low to Data Out Valid 0.1 4.5 0.1 4.5 0.1 0.9 µs Time the bus must be free before a new transmission can start(1) 4.7 4.7 1.2 µs tHD.STA Start Hold Time 4.0 4.0 tSU.STA Start Set-up Time 4.7 4.7 tHD.DAT Data In Hold Time 0 0 tSU.DAT tR tF Data In Set-up Time Inputs Rise Time(1) Inputs Fall Time(1) 200 200 1.0 300 tSU.STO Stop Set-up Time 4.7 4.7 tDH Data Out Hold Time 100 100 tWR Endurance(1) Write Cycle Time 5.0V, 25°C, Page Mode 20 1M 1M Note: 1. This parameter is characterized and is not 100% tested. 0.6 µs 0.6 µs 0 µs 100 ns 1.0 0.3 µs 300 300 ns 0.6 µs 50 ns 10 10 ms 1M Write Cycles Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (refer to Data Validity timing diagram). Data changes during SCL high periods will indicate a start or stop condition as defined below. START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (refer to Start and Stop Definition timing diagram). STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode (refer to Start and Stop Definition timing diagram). ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a zero during the ninth clock cycle to acknowledge that it has received each word. STANDBY MODE: The AT24C32/64 features a low power standby mode which is enabled: a) upon power-up and b) after the receipt of the STOP bit and the completion of any internal operations. MEMORY RESET: After an interruption in protocol, power loss or system reset, any 2-wire part can be reset by following these steps: (a) Clock up to 9 cycles, (b) look for SDA high in each cycle while SCL is high and then (c) create a start condition as SDA is high. 4 AT24C32/64 Bus Timing SCL: Serial Clock, SDA: Serial Data I/O AT24C32/64 Write Cycle Timing SCL: Serial Clock, SDA: Serial Data I/O tWR(1) Note: 1. The write cycle time tWR is the time from a valid stop condition of a write sequence to the end of the internal clear/write cycle. 5 Data Validity Start and Stop Definition Output Acknowledge 6 AT24C32/64 AT24C32/64 Device Addressing The 32K/64K EEPROM requires an 8-bit device address word following a start condition to enable the chip for a read or write operation (refer to Figure 1). The device address word consists of a mandatory one, zero sequence for the first four most significant bits as shown. This is common to all 2-wire EEPROM devices. The 32K/64K uses the three device address bits A2, A1, A0 to allow as many as eight devices on the same bus. These bits must compare to their corresponding hardwired input pins. The A2, A1, and A0 pins use an internal proprietary circuit that biases them to a logic low condition if the pins are allowed to float. The eighth bit of the device address is the read/write operation select bit. A read operation is initiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a zero. If a compare is not made, the device will return to standby state. NOISE PROTECTION: Special internal circuitry placed on the SDA and SCL pins prevent small noise spikes from activating the device. A low-VCC detector (5-volt option) resets the device to prevent data corruption in a noisy environment. DATA SECURITY: The AT24C32/64 has a hardware data protection scheme that allows the user to write protect the upper quadrant (8/16K bits) of memory when the WP pin is at VCC. Write Operations BYTE WRITE: A write operation requires two 8-bit data word addresses following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a zero and the addressing device, such as a microcontroller, must terminate the write sequence with a stop condition. At this time the EEPROM enters an internally-timed write cycle, tWR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (refer to Figure 2). PAGE WRITE: The 32K/64K EEPROM is capable of 32byte page writes. A page write is initiated the same way as a byte write, but the microcontroller does not send a stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to 31 more data words. The EEPROM will respond with a zero after each data word received. The microcontroller must terminate the page write sequence with a stop condition (refer to Figure 3). The data word address lower 5 bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the same page. If more than 32 data words are transmitted to the EEPROM, the data word address will “roll over” and previous data will be overwritten. ACKNOWLEDGE POLLING: Once the internally-timed write cycle has started and the EEPROM inputs are disabled, acknowledge polling can be initiated. This involves sending a start condition followed by the device address word. The read/write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a zero, allowing the read or write sequence to continue. Read Operations Read operations are initiated the same way as write operations with the exception that the read/write select bit in the device address word is set to one. There are three read operations: current address read, random address read and sequential read. CURRENT ADDRESS READ: The internal data word address counter maintains the last address accessed during the last read or write operation, incremented by one. This address stays valid between operations as long as the chip power is maintained. The address “roll over” during read is from the last byte of the last memory page, to the first byte of the first page. The address “roll over” during write is from the last byte of the current page to the first byte of the same page. Once the device address with the read/write select bit set to one is clocked in and acknowledged by the EEPROM, the current address data word is serially clocked out. The microcontroller does not respond with an input zero but does generate a following stop condition (refer to Figure 4). RANDOM READ: A random read requires a “dummy” byte write sequence to load in the data word address. Once the device address word and data word address are clocked in and acknowledged by the EEPROM, the microcontroller must generate another start condition. The microcontroller now initiates a current address read by sending a device address with the read/write select bit high. The EEPROM acknowledges the device address and serially clocks out the data word. The microcontroller does not respond with a zero but does generate a following stop condition (refer to Figure 5). SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a random address read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an 7 acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will “roll over” and the sequential read will con- Figure 1. Device Address tinue. The sequential read operation is terminated when the microcontroller does not respond with a zero but does generate a following stop condition (refer to Figure 6). Figure 2. Byte Write Figure 3. Page Write Notes: 1. * = DON’T CARE bits Figure 4. Current Address Read 2. † = DON’T CARE bits for the 32K Figure 5. Random Read Note: 1. * = DON’T CARE bits 8 AT24C32/64 Figure 6. Sequential Read AT24C32/64 9 AT24C32 Ordering Information tWR (max) (ms) 10 ICC (max) (µA) 3000 ISB (max) (µA) 35 fMAX (kHz) 400 3000 35 400 10 1500 0.5 100 1500 0.5 100 Ordering Code AT24C32-10PC AT24C32N-10SC AT24C32W-10SC AT24C32-10TC AT24C32-10SC AT24C32-10PI AT24C32N-10SI AT24C32W-10SI AT24C32-10TI AT24C32-10SI AT24C32-10PC-2.7 AT24C32N-10SC-2.7 AT24C32W-10SC-2.7 AT24C32-10TC-2.7 AT24C32-10SC-2.7 AT24C32-10PI-2.7 AT24C32N-10SI-2.7 AT24C32W-10SI-2.7 AT24C32-10TI-2.7 AT24C32-10SI-2.7 Package 8P3 8S1 8S2 8T 14S 8P3 8S1 8S2 8T 14S 8P3 8S1 8S2 8T 14S 8P3 8S1 8S2 8T 14S Operation Range Commercial (0°C to 70°C) Industrial (-40°C to 85°C) Commercial (0°C to 70°C) Industrial (-40°C to 85°C) 8P3 8S1 8S2 8T 14S Blank -2.7 -2.5 -1.8 10 Package Type 8-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8-Lead, 0.200" Wide, Plastic Gull Wing Small Outline (EIAJ SOIC) 8-Lead, 0.170" Wide, Plastic Gull Wing Small Outline (TSSOP) 14-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (SOIC) Options Standard Operation (4.5V to 5.5V) Low Voltage (2.7V to 5.5V) Low Voltage (2.5V to 5.5V) Low Voltage (1.8V to 5.5V) AT24C32/64 AT24C32 Ordering Information (Continued) tWR (max) (ms) 10 ICC (max) (µA) 1000 ISB (max) (µA) 0.5 fMAX (kHz) 100 1000 0.5 100 10 800 0.1 100 800 0.1 100 Ordering Code AT24C32-10PC-2.5 AT24C32N-10SC-2.5 AT24C32W-10SC-2.5 AT24C32-10TC-2.5 AT24C32-10SC-2.5 AT24C32-10PI-2.5 AT24C32N-10SI-2.5 AT24C32W-10SI-2.5 AT24C32-10TI-2.5 AT24C32-10SI-2.5 AT24C32-10PC-1.8 AT24C32N-10SC-1.8 AT24C32W-10SC-1.8 AT24C32-10TC-1.8 AT24C32-10SC-1.8 AT24C32-10PI-1.8 AT24C32N-10SI-1.8 AT24C32W-10SI-1.8 AT24C32-10TI-1.8 AT24C32-10SI-1.8 AT24C32/64 Package 8P3 8S1 8S2 8T 14S 8P3 8S1 8S2 8T 14S 8P3 8S1 8S2 8T 14S 8P3 8S1 8S2 8T 14S Operation Range Commercial (0°C to 70°C) Industrial (-40°C to 85°C) Commercial (0°C to 70°C) Industrial (-40°C to 85°C) 8P3 8S1 8S2 8T 14S Blank -2.7 -2.5 -1.8 Package Type 8-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8-Lead, 0.200" Wide, Plastic Gull Wing Small Outline (EIAJ SOIC) 8-Lead, 0.170" Wide, Plastic Gull Wing Small Outline (TSSOP) 14-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (SOIC) Options Standard Operation (4.5V to 5.5V) Low Voltage (2.7V to 5.5V) Low Voltage (2.5V to 5.5V) Low Voltage (1.8V to 5.5V) 11 AT24C64 Ordering Information tWR (max) (ms) 10 ICC (max) (µA) 3000 ISB (max) (µA) 35 fMAX (kHz) 400 3000 35 400 10 1500 0.5 100 1500 0.5 100 Ordering Code AT24C64-10PC AT24C64N-10SC AT24C64W-10SC AT24C64-10TC AT24C64-10SC AT24C64-10PI AT24C64N-10SI AT24C64W-10SI AT24C64-10TI AT24C64-10SI AT24C64-10PC-2.7 AT24C64N-10SC-2.7 AT24C64W-10SC-2.7 AT24C64-10TC-2.7 AT24C64-10SC-2.7 AT24C64-10PI-2.7 AT24C64N-10SI-2.7 AT24C64W-10SI-2.7 AT24C64-10TI-2.7 AT24C64-10SI-2.7 Package 8P3 8S1 8S2 8T 14S 8P3 8S1 8S2 8T 14S 8P3 8S1 8S2 8T 14S 8P3 8S1 8S2 8T 14S Operation Range Commercial (0°C to 70°C) Industrial (-40°C to 85°C) Commercial (0°C to 70°C) Industrial (-40°C to 85°C) 8P3 8S1 8S2 8T 14S Blank -2.7 -2.5 -1.8 12 Package Type 8-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8-Lead, 0.200" Wide, Plastic Gull Wing Small Outline (EIAJ SOIC) 8-Lead, 0.170" Wide, Plastic Gull Wing Small Outline (TSSOP) 14-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (SOIC) Options Standard Operation (4.5V to 5.5V) Low Voltage (2.7V to 5.5V) Low Voltage (2.5V to 5.5V) Low Voltage (1.8V to 5.5V) AT24C32/64 AT24C64 Ordering Information (Continued) tWR (max) (ms) 10 ICC (max) (µA) 1000 ISB (max) (µA) 0.5 fMAX (kHz) 100 1000 0.5 100 10 800 0.1 100 800 0.1 100 Ordering Code AT24C64-10PC-2.5 AT24C64N-10SC-2.5 AT24C64W-10SC-2.5 AT24C64-10TC-2.5 AT24C64-10SC-2.5 AT24C64-10PI-2.5 AT24C64N-10SI-2.5 AT24C64W-10SI-2.5 AT24C64-10TI-2.5 AT24C64-10SI-2.5 AT24C64-10PC-1.8 AT24C64N-10SC-1.8 AT24C64W-10SC-1.8 AT24C64-10TC-1.8 AT24C64-10SC-1.8 AT24C64-10PI-1.8 AT24C64N-10SI-1.8 AT24C64W-10SI-1.8 AT24C64-10TI-1.8 AT24C64-10SI-1.8 AT24C32/64 Package 8P3 8S1 8S2 8T 14S 8P3 8S1 8S2 8T 14S 8P3 8S1 8S2 8T 14S 8P3 8S1 8S2 8T 14S Operation Range Commercial (0°C to 70°C) Industrial (-40°C to 85°C) Commercial (0°C to 70°C) Industrial (-40°C to 85°C) 8P3 8S1 8S2 8T 14S Blank -2.7 -2.5 -1.8 Package Type 8-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8-Lead, 0.200" Wide, Plastic Gull Wing Small Outline (EIAJ SOIC) 8-Lead, 0.170" Wide, Plastic Gull Wing Small Outline (TSSOP) 14-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (SOIC) Options Standard Operation (4.5V to 5.5V) Low Voltage (2.7V to 5.5V) Low Voltage (2.5V to 5.5V) Low Voltage (1.8V to 5.5V) 13 Packaging Information 8P3, 8-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-001 BA .400 (10.16) .355 (9.02) PIN 1 .300 (7.62) REF .280 (7.11) .240 (6.10) .037 (.940) .027 (.690) .210 (5.33) MAX SEATING PLANE .100 (2.54) BSC .150 (3.81) .115 (2.92) .070 (1.78) .045 (1.14) .015 (.380) MIN .022 (.559) .014 (.356) .012 (.305) .008 (.203) .325 (8.26) .300 (7.62) 0 15 REF .430 (10.9) MAX 8S2, 8-Lead, 0.200" Wide, Plastic Gull Wing Small Outline (EIAJ SOIC) Dimensions in Inches and (Millimeters) .020 (.508) .012 (.305) PIN 1 .213 (5.41) .330 (8.38) .205 (5.21) .300 (7.62) .050 (1.27) BSC .212 (5.38) .203 (5.16) .080 (2.03) .070 (1.78) .013 (.330) .004 (.102) 0 8 REF .035 (.889) .020 (.508) .010 (.254) .007 (.178) 14 AT24C32/64 8S1, 8-Lead, 0150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) Dimensions in Inches and (Millimeters) .020 (.508) .013 (.330) PIN 1 .157 (3.99) .244 (6.20) .150 (3.81) .228 (5.79) .050 (1.27) BSC .196 (4.98) .189 (4.80) .068 (1.73) .053 (1.35) .010 (.254) .004 (.102) 0 8 REF .050 (1.27) .016 (.406) .010 (.254) .007 (.203) 8T, 8-Lead, Plastic Thin Small Outline Package (TSSOP) Dimensions in Millimeters and (Inches)* PIN 1 6.50 (.256) 6.25 (.246) 0.30 (.012) 0.19 (.008) 1.05 (.041) 0.80 (.033) 3.10 (.122) 2.90 (.114) 1.20 (.047) MAX .65 (.026) BSC 0.15 (.006) 0.05 (.002) 4.5 (.177) 4.3 (.169) 0 REF 8 0.75 (.030) 0.45 (.018) *Controlling dimension: millimeters 0.20 (.008) 0.09 (.004) Packaging Information 14S, 14-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (SOIC) Dimensions in Inches and (Millimeters) .020 (.508) .013 (.330) PIN 1 .158 (4.01) .244 (6.20) .152 (3.86) .228 (5.79) .050 (1.27) BSC .344 (8.74) .337 (8.56) .068 (1.73) .053 (1.35) .010 (.249) .004 (.102) 0 8 REF .050 (1.27) .016 (.406) .010 (.249) .008 (.191) AT24C32/64 15

Top_arrow
回到顶部
EEWORLD下载中心所有资源均来自网友分享,如有侵权,请发送举报邮件到客服邮箱bbs_service@eeworld.com.cn 或通过站内短信息或QQ:273568022联系管理员 高进,我们会尽快处理。