doc

ANSALDO直流调速器

  • 1星
  • 日期: 2016-01-16
  • 大小: 609KB
  • 所需积分:2分
  • 下载次数:3
  • favicon收藏
  • rep举报
  • free评论
标签: 速度调节器比例增益

速度调节器比例增益

填写文档简介,能帮助文档传播更广~

文档内容节选

ANSALDO参数表 地址 类型 代码 名称 说明 默认值 实际值 实际值 实际值 设定范围 CA 电流调节器 258 2 CA1 IaoSI 选择电枢电流给定源 NReg 6种 259 2 CA2 IaoLm 选择电枢电流限幅 Fixed 7种 260 2 CA3 IaoAd 选择电枢电流附加给定源 OFF 6种 261 8 CA4 IaoWo 来自速调输出的电流给定滤波值 0 0255 rs 262 3 CA5 RateL 来自速度环的电枢电流变化率限幅 100 0100 264 3 CA6 IaLNM 基速到最高速中电枢电流限幅修正 100 01100 266 8 CA7 NMDel 零流信号后,电枢电流反向过程的延时 0 0255 268 3 CA8 InThr 电枢电流零电流门限值 2 050 270 3 CA9 IaLim 电流限幅设置 100 0100 CB 速度调节器 ......

ANSALDO参数表 地址 |类型 |代码 |名称 |说明 |默认值 |实际值 |实际值 |实际值 |设定范围 | | | | | | | | | | | | | | | | |CA 电流调节器 | | | | | | |258 |2 |CA1 |IaoSI |选择电枢电流给定源 |N_Reg | | | |6种 | |259 |2 |CA2 |IaoLm |选择电枢电流限幅 |Fixed | | | |7种 | |260 |2 |CA3 |IaoAd |选择电枢电流附加给定源 |OFF | | | |6种 | |261 |8 |CA4 |IaoWo |来自速调输出的电流给定滤波值 |0 | | | |0-255 r/s | |262 |3 |CA5 |RateL |来自速度环的电枢电流变化率限幅 |100% | | | |0-100% | |264 |3 |CA6 |IaLNM |基速到最高速中电枢电流限幅修正 |100% | | | |0.1-100% | |266 |8 |CA7 |NMDel |零流信号后,电枢电流反向过程的延时 |0 | | | |0-255 | |268 |3 |CA8 |InThr |电枢电流零电流门限值 |2% | | | |0-50% | |270 |3 |CA9 |IaLim |电流限幅设置 |100% | | | |0-100% | | | | | | | | | | | | | | | | |CB 速度调节器 | | | | | | | | |CBA |Enable |速度调节器使能 |ON | | | |ON/OFF | | | |CBB |Enc_F |编码器速度反馈滤波使能 |OFF | | | |ON/OFF | | | |CBC |Int=0 |速度给定=0时,积分器输出强制为0 |OFF | | | |ON/OFF | | | |CBD |Rmp_B |给定积分使能(XM1-14有关) |OFF | | | |ON/OFF | | | |CBE |MpoMem |EEPROM存储软件电动电位计上一次设置的给定 |OFF | | | |ON/OFF | | | |CBF |MpoRes |速度=0时,软件电位器最后一次给定清0 |OFF | | | |ON/OFF | | | |CBG |TacFUd |测速反馈丢失时,电枢电压作速度反馈 |OFF | | | |ON/OFF | | | |CBH |Wo_Ref |卷径测量时角速度计算功能使能 |OFF | | | |ON/OFF | |288 |1 |CB0 |Sp_Bs |(通讯用) | | | | | | |289 |2 |CB1 |No_Sel |选择速度给定源 |MpotFw | | | |7种 | |290 |2 |CB2 |MoAdd |选择附加速度给定源 |OFF | | | |6种 | |291 |2 |CB3 |N-Sel |选择速度反馈源 |Encod | | | |4种 | |292 |4 |CB4 |Mtime |软件自动电位计斜率时间 |10.1s | | | |0.1-999.9s | |294 |3 |CB5 |Nstop |零速门限 |2% | | | |0-10% | |296 |3 |CB6 |Nhist |零速门限回环宽度 |0.3% | | | |0-10% | |298 |3 |CB7 |ErNLm |达速信号门限 |1% | | | |0-10% | |300 |3 |CB8 |Enc-R |编码器反馈的休正 |100% | | | |0-200% | |302 |3 |CB9 |M_Ref |由软件自动电位计设置的最终速度给定 |0 | | | |0-200% | | | | | | | | | | | | | | | | |CC 电势调节器 | | | | | | | | |CCA |Enable |电势`调节器使能 |ON | | | |ON/OFF | | | |CCB |Fld_In |磁场可逆辅助功能使能 |OFF | | | |ON/OFF | | | |CCC |Fld0_P |变流器在保护状态下,励磁给定为0 |ON | | | |ON/OFF | |322 |1 |CC0 |EMFBs |(通讯用)) | | | | | | |324 |3 |CC1 |Fecon |经济磁场 |100% | | | |0-100% | |326 |8 |CC2 |FIDel |励磁反向使能延时时间 |10 | | | |0-250 | |328 |6 |CC3 |FecTm |经济磁场延时时间 |1000 | | | |0-1999 | |330 |3 |CC4 |FLXmn |速调采用电压反馈时的磁通值 |100% | | | |10-100% | | | | | | | | | | | | | | | | |CD 其他控制参数 | | | | | | | | |CDA |W_Eepr |参数存储在EEPROM使能 |ON | | | |ON/OFF | | | |CDB |QuickS |电机快速重新起动功能使能 |OFF | | | |ON/OFF | | | |CDC |Diesel |变流器由一台发电机供电功能使能 |OFF | | | |ON/OFF | | | |CDD |EncAbs |编码器速度反馈取绝对值 |OFF | | | |ON/OFF | | | |CDE |IR12Ds |禁止IntRf1和IntRf2命令代替Start命令 |OFF | | | |ON/OFF | | | |CDF |OFF |所有参数恢复默认值 |OFF | | | |ON/OFF | |346 |1 |CD0 |Ms_Bs | | | | | | | |347 |2 |CD1 |RunEn |START输入=运行 |Run_1 | | | |3种 | |348 |2 |CD2 |Del% |显示满刻度的百分数 |% | | | |% / Real | |349 |2 |CD3 |Cyc_T |循环时间 |10ms | | | |10,5,3.3ms | |350 |8 |CD4 |AbDel |从X13输入使能到变流器脉冲输出的时间 |15 | | | |1-255 | |351 |8 |CD5 |Nz_D |达到零速后继电器K1断开的延时 |0 | | | |0-255 | |352 |3 |CD6 |N-MxV |每循环允许的最大速度反馈变化量 |100% | | | |0.1-100% | |354 |8 |CD7 |N_Flt |速度反馈的输入滤波值 |0 | | | |0-255 r/s | |355 |8 |CD8 |NST_G |通过速度自优化修正速调的频带宽度 |0 | | | |0-200 | |356 |3 |CD9 |IlThr |电流极限信号门限值 |5% | | | |0-10% | | | | | | | | | | | | | | | | |CE 辅助功能1 | | | | | | | | |CEA |Helper |Helper辅助功能启动 |OFF | | | |ON/OFF | | | |CEB |Pope |Pope辅助功能启动 |OFF | | | |ON/OFF | | | |CEC |Step |Step辅助功能启动 |OFF | | | |ON/OFF | | | |CED |Mloss |机械损耗补偿辅助功能启动 |OFF | | | |ON/OFF | | | |CEF |Kramer |Kramer辅助功能启动 |OFF | | | |ON/OFF | |372 |1 |CE0 |Ax_Bs | | | | | | | |374 |3 |CE1 |NoRic |附加速度给定值(速度偏置) |10% | | | |0-20% | |376 |3 |CE2 |S_Thr |电流反馈超过该门限时,允许叠加附加电流给定 |10% | | | |0- 100% | |378 |3 |CE3 |LossK |机械摩擦损失固定值 |10% | | | |0-100% | |380 |3 |CE4 |LK_N |与速度成线性的机械摩擦损失补偿系数 |10% | | | |0-100% | |382 |3 |CE5 |IaThr |电流门限值 |10% | | | |0-100% | |384 |3 |CE6 |N_Thr |速度门限值 |10% | | | |0-100% | |386 |6 |CE7 |K_Gn |Kramer调节器的比例增益 |0 | | | |0-9999 | |388 |3 |CE8 |NLRic |速度门限值,超过后电流限幅修正功能启动 |0 | | | |0-100% | |390 |3 |CE9 |Ir_TM |与电机有关的电机热保护校正值 |100 | | | |100-200% | | | | | | | | | | | | | | | | |CF 辅助功能2 | | | | | | | | |CFA |G_Ric |做卷取应用时速度调节器增益的修正 |OFF | | | |ON/OFF | | | |CFB |T_Prf |Torque-proof转矩检测功能启动 |OFF | | | |ON/OFF | | | |CFC |L_W |Load Weighting重物提升功能启动 |OFF | | | |ON/OFF | | | |CFD |FTR |Fixed time Ramp固定时间斜率功能启动 |OFF | | | |ON/OFF | | | |CFE |Flux_R |弱磁时,速调增益修正功能启动 |OFF | | | |ON/OFF | | | |CFF |Fud_C3 |根据COM3选择基速和速度反馈源 |OFF | | | |ON/OFF | |400 |1 |CF0 |Ax_Bs | | | | | | | |402 |3 |CF1 |TPLim |在抱闸打开前电流限幅值 |10% | | | |0-100% | |404 |8 |CF2 |TP_T |参数CF1有效时的时间 |100 | | | |0-255 | |406 |3 |CF3 |LW_Fr |摩擦转矩损耗补偿参数 |10% | | | |0-100% | |408 |4 |CF4 |RmpTM |固定时间斜率的设定时间 |10s | | | |0.1-999.9s | |410 |8 |CF5 |Tf(D) |用软件循环周期表示的滞后时间 |0 | | | |0-255 | |411 |8 |CF6 |LW_Tm |重物提升功能的Weighting时间 |50 | | | |1-127 | |412 |3 |CF7 |ErNar |速度偏差门限值(给定积分后),用于DO |10% | | | |0-20% | |414 |8 |CF8 |ErN_T |速度偏差超CF7时逻辑输出动作的时间 |10 | | | |0-250 | | | | | | | | | | | | | | | | |调试参数 | | | | | | | | | | |TA 电流调节器 | | | | | | | | |TA1 |G_p1 |1st电流调节器比例增益 |32 | | | |0-9999 | | | |TA2 |G_d1 |1st电流调节器微分增益 |56 | | | |0-255 | | | |TA3 |IaTL1 |1st电流上限幅,IaM的百分数 |100% | | | |±100% | | | |TA4 |IaBL1 |1st电流下限幅,IaM的百分数 |-100% | | | |±100% | | | |TA5 |Iaof1 |附加电枢电流给定,由CA3选择 |0 | | | |±100% | | | | | | | | | | | | | | | | |TB 电流调节器 | | | | | | | | |TB1 |G_p2 |2nd电流调节器比例增益 |32 | | | |0-9999 | | | |TB2 |G_d2 |2nd电流调节器微分增益 |56 | | | |0-255 | | | |TB3 |IaTL2 |2nd电流上限幅,IaM的百分数 |100% | | | |±100% | | | |TB4 |IaBL2 |2nd电流下限幅,IaM的百分数 |-100% | | | |±100% | | | |TB5 |Iaof2 |附加电枢电流给定,由CA3选择 |0 | | | |±100% | | | | | | | | | | | | | | | | |TC 速度调节器 | | | | | | | | |TC1 |N_Gp1 |1st速度调节器比例增益 |400 | | | |0-9999 | | | |TC2 |N_Gi1 |1st速度调节器积分增益 |80 | | | |0-8000 | | | |TC3 |N_Gd1 |1st速度调节器微分增益 |0 | | | |0-255 | | | |TC4 |NoLa1 |1st正向速度限幅 |100% | | | |0-+120% | | | |TC5 |NoLI1 |1st反向速度限幅 |- 100% | | | |-120%-0 | | | |TC6 |NoOf1 |1st附加速度给定,由CB2选择 |0 | | | |±100% | | | |TC7 |InR11 |X15有效,内部给定1-1作为速度给定 |30% | | | |±100% | | | |TC8 |InR21 |X15有效,内部给定1-2作为速度给定 |-30% | | | |±100% | | | |TC9 |Ced1 |1st辅基机特性,使电机特性变软 |0 | | | |0-10% | | | | | | | | | | | | | | | | |TD 速度调节器 | | | | | | | | |TD1 |N_Gp2 |2nd速度调节器比例增益 |400 | | | |0-9999 | | | |TD2 |N_Gi2 |2nd速度调节器积分增益 |80 | | | |0-8000 | | | |TD3 |N_Gd2 |2nd速度调节器微分增益 |0 | | | |0-255 | | | |TD4 |NoLa2 |2nd正向速度限幅 |100% | | | |0-+120% | | | |TD5 |NoLI2 |2nd反向速度限幅 |-100% | | | |-120%- 0 | | | |TD6 |NoOf2 |2nd附加速度给定,由CB2选择 |0 | | | |±100% | | | |TD7 |InR12 |X15有效,内部给定1-1作为速度给定 |30% | | | |±100% | | | |TD8 |InR22 |X15有效,内部给定1-2作为速度给定 |-30% | | | |±100% | | | |TD9 |Ced2 |2nd辅基机特性,使电机特性变软 |0 | | | |0-10% | | | | | | | | | | | | | | | | |TE 给定积分 | | | | | | | | |TE1 |TacR1 |1st电机从0到100%加速斜率时间 |10s | | | |0.1-999.9s | | | |TE2 |TdcR1 |1st电机从100%到0减速斜率时间 |10s | | | |0.1-999.9s | | | |TE3 |TarRm |S曲线调整时间 |0 | | | |0-7.5s | | | | | | | | | | | | | | | | |TF 给定积分 | | | | | | | | |TF1 |TacR2 |2nd电机从0到100%加速斜率时间 |10s | | | |0.1-999.9s | | | |TF2 |TdcR2 |2nd电机从100%到0减速斜率时间 |10s | | | |0.1-999.9s | | | | | | | | | | | | | | | | |TG 电势调节器 | | | | | | | | |TG1 |E_Gp |电机电动势调节器的比例增益 |100 | | | |0-9999 | | | |TG2 |E_Gi |电机电动势调节器的积分增益 |16 | | | |0-8000 | | | | | | | | | | | | | | | | |TH 速调增益调整 | | | | | | | | |TH1 |Gp_K1 |3rd速度调节器比例增益 |400 | | | |0-9999 | | | |TH2 |Gi_K1 |3rd速度调节器积分增益 |80 | | | |0- 8000 | | | |TH3 |Gd_K1 |3rd速度调节器微分增益 |0 | | | |0-255 | | | |TH4 |Gp_K2 |4th速度调节器比例增益 |400 | | | |0-9999 | | | |TH5 |Gi_K2 |4th速度调节器积分增益 |80 | | | |0-8000 | | | |TH6 |Gd_K2 |4th速度调节器微分增益 |0 | | | |0-255 | | | |TH7 |TcFGp |速度反馈变为电枢电压反馈时的速度`调节器比例增益 |0 | | | |0-9999 | | | |TH8 |TcFGi |速度反馈变为电枢电压反馈时的速度`调节器积分增益 |0 | | | |0- 8000 | | | | | | | | | | | | | | | | |装置参数 | | | | | | | | | | |DA 装置标识 | | | | | | |514 |6 |DA1 |Snumb |Silcopac D设备编号 |0 | | | |0- 9999 | |516 |2 |DA2 |Bridg |选择变流器的工作方式 |Unid | | | |Unid/Rev | |517 |2 |DA3 |Thyr |变流器容量选择 |30 | | | |30~4K0 | | | | | | | | | | | | | | | | |DB 装置输入/输出 | | | | | | |524 |6 |DB1 |UvoFs |线电压满刻度值选择(供电电压) |380V | | | |0-999.9V | |526 |7 |DB2 |If_Fs |励磁电流满刻度值 |3A | | | |0-999.9A | |528 |6 |DB3 |Ia_Fs |变流器电流满刻度值 |30A | | | |0-9999A | |530 |6 |DB4 |Ud_Fs |电枢电压满刻度值 |400V | | | |0-1000V | |532 |6 |DB5 |N_fs |电机转速满刻度值 |2000 | | | |0-9999rpm | |534 |3 |DB6 |IaNom |电机额定电流相对于IaM的百分值 |100% | | | |0-100% | |536 |3 |DB7 |Nbase |电机基速相对于最高速度的百分值 |100% | | | |0-100% | |538 |6 |DB8 |Enc_P |编码器每转的脉冲数 |500 | | | |0-9999 | |540 |3 |DB9 |RI% |电枢电流等于100%IaM,R*I的压降相对于参数DB4的百分值 |0 | | | |0-100% | | | | | | | | | | | | | | | | |DC 保护 | | | | | | | | |DCA |MainF |(0)缺相,推β,脉冲封锁 |ON | | | |ON/OFF | | | |DCB |Ext_P |(1)外部保护(X20)无效 |ON | | | |ON/OFF | | | |DCC |IOC |(2)最大瞬时电流(3.15*IaM) |ON | | | |ON/OFF | | | |DCD |W_Dog |(3)看门狗 |ON | | | |ON/OFF | | | |DCE |Ud_F |(4)最大电枢电压 |ON | | | |ON/OFF | | | |DCF |If_F |(5)电机失磁 |ON | | | |ON/OFF | | | |DCG |Tach_F |(6)测速丢失 |ON | | | |ON/OFF | | | |DCH |Fan_F |(7)风机故障 |ON | | | |ON/OFF | | | |DCI |MotOh |(8)电机热保护 |ON | | | |ON/OFF | | | |DCJ |ConOh |(9)变流器热保护 |ON | | | |ON/OFF | | | |DCK |Ser_F |(10)串行通讯故障 |ON | | | |ON/OFF | | | |DCL |N_Max |(11)电机最大转速 |ON | | | |ON/OFF | | | |DCM |UvOut |(12)电源超出范围 |ON | | | |ON/OFF | | | |DCN |Stale |(13)电机堵转 |ON | | | |ON/OFF | | | |DCO |Leg_F |(14)桥臂故障 |ON | | | |ON/OFF | |550 |1 |DC0 |Pr0Bs | | | | | | | |551 |1 |DC0 |Pr1Bs | | | | | | | |552 |3 |DC1 |UvoMn |欠电压保护门限值 |80% | | | |75-100% | |554 |3 |DC2 |UvoMx |过电压保护门限值 |115% | | | |100-120% | |556 |3 |DC3 |Fld_L |欠磁保护门限值 |10% | | | |1-50% | |558 |3 |DC4 |N_Max |电机最大速度保护门限值 |115% | | | |0-124% | |560 |3 |DC5 |UdMax |最大电枢电压保护门限值 |120% | | | |100-124% | |562 |5 |DC6 |Tstal |从堵转发生到保护动作的时间 |5s | | | |0-25s | |563 |8 |DC7 |Sncic |从串行接口故障发生到保护动作的时间 |100 | | | |2-250 | |564 |3 |DC8 |MOH_R |电机热保护动作门限值的修正 |100% | | | |0-150% | |566 |3 |DC9 |Fld_T |励磁电流反馈允许偏差值 |20% | | | |0-50% | | | | | | | | | | | | | | | | |DD 报警 | | | | | | | | |DDA |Tach_F |测速丢失 |OFF | | | |ON/OFF | | | |DDB |Fan_F |风机故障 |OFF | | | |ON/OFF | | | |DDC |MotOh |电机热保护 |OFF | | | |ON/OFF | | | |DDD |ConOh |变流器热保护 |OFF | | | |ON/OFF | | | |DDE |Ser_F |串行通讯故障 |OFF | | | |ON/OFF | | | |DDF |Stale |电机堵转 |OFF | | | |ON/OFF | |572 |1 |DD0 |AI0Bs |DDA:Bit6, DDB:Bit7 | | | | | | |573 |1 |DD0 |AI1Bs |DDC:Bit0; DDD:Bit1; DDF:Bit5 | | | | | | |574 |8 |DD1 |ResA1 |报警软件复位 |0 | | | |0 / 1 | | | | | | | | | | | | | | | | |DE串行口通讯 | | | | | | | | |DEA |Enable |串行口通讯使能 | | | | | | | | |DEB |S_Com |串行口通讯逻辑功能使能 | | | | | | | | |DEC |S_PC |用个人计算机进行串行口通讯使能 | | | | | | | | |DED |S_Par |通过串行口通讯改变参数使能 | | | | | | | | |DEE |S_Cum |通过串行口通讯接受信息使能 | | | | | | | | |DEF |S_ComD |通过串行口禁止逻辑命令 | | | | | | | | |DEG |S_D2 |通过串口通讯传输诊断DATABASE数据库使能 | | | | | | | | |DEH |S_PLC |PLC通讯使能 | | | | | | |582 |1 |DE0 |Se_Bs |DEA: Bit 0 DEB:Bit1; DEC: Bit 2 | | | | | | |583 |2 |DE1 |BaudR |串行口通讯的薄特率波特率 | | | | | | |584 |8 |DE2 |IdNum |变流器识别号 | | | | | | |585 |8 |DE3 |Ser_D |串行中断的执行时间 | | | | | | | | | | | | | | | | | | | | | |DF 串行数据 | | | | | | | | |DFA |D1_n |记录数N | | | | | | | | |DFB |D1_Sts |状态 | | | | | | | | |DFC |D1LPro |保护 低字节 | | | | | | | | |DFD |D1HPro |保护 高字节 | | | | | | | | |DFE |D1LAbi |逻辑I/O 低字节 | | | | | | | | |DFF |D1HAbi |逻辑I/O 高字节 | | | | | | | | |DFG |D1LAu1 |Aux1 低字节 | | | | | | | | |DFH |D1HAu1 |Aux1 高字节 | | | | | | | | |DFI |D1LAu2 |Aux2 低字节 | | | | | | | | |DFJ |D1HAu2 |Aux2 高字节 | | | | | | | | |DFK |D1LAu3 |Aux3 低字节 | | | | | | | | |DFL |D1HAu3 |Aux3 高字节 | | | | | | | | |DFM |D1LNo |No速度给定 低字节 | | | | | | | | |DFN |D1HNo |No速度给定 高字节 | | | | | | | | |DFO |D1L_N |N速度反馈 低字节 | | | | | | | | |DFP |D1H_N |N速度反馈 高字节 | | | | | | | | |Dfa |D1LIao |电枢电流给定 低字节 | | | | | | | | |DFb |D1HIao |电枢电流给定 高字节 | | | | | | | | |DFc |D1L_Ia |电枢电流反馈 低字节 | | | | | | | | |DFd |D1H_Ia |电枢电流反馈 高字节 | | | | | | | | |Dfe |D1L_Ud |电枢电压 低字节 | | | | | | | | |DFf |D1H_Ud |电枢电压 高字节 | | | | | | | | |DFg |D1LFlu |电机磁通 低字节 | | | | | | | | |DFh |D1HFlu |电机磁通 高字节 | | | | | | | | |Dfi |D1LIfo |磁场电流给定 低字节 | | | | | | | | |DFj |D1HIfo |磁场电流给定 高字节 | | | | | | | | |DFk |D1L_If |磁场电流反馈 低字节 | | | | | | | | |DFl |D1H_If |磁场电流反馈 高字节 | | | | | | | | |DFm |D1LUvo |电源线电压 低字节 | | | | | | | | |DFn |D1HUvo |电源线电压 高字节 | | | | | | | | |Dfo |D1L_a |晶闸管触发角 低字节 | | | | | | | | |DFp |DiH_a |晶闸管触发角 高字节 | | | | | | |594 |1 |DF0 |D1Bs1 |DFA~DFH:Bit0~Bit7 | | | | | | |595 |1 |DF0 |D1Bs2 |DFI~DFK:Bit0~Bit2 | | | | | | | | | | | | | | | | | | | | | |DG诊断 | | | | | | | | |DGA |TStop |Stop和Traces存储 |OFF | | | |ON/OFF | | | |DGB |SStop |当设置给定SETUP REFERENCE功能使能时,Stop和Traces存储 |OFF | | | |ON/OFF | | | |DGC |Inst_M |`装置得电或复位后显示方式选择 |OFF | | | |ON/OFF | |606 |1 |DG0 |Di_Bs | | | | | | | |607 |8 |DG1 |TrcNr |在封锁后DRIVE TRACE的记录号 |25 | | | |5-45 | |608 |8 |DG2 |TrcNc |设置DRIVE TRACE中两个记录点间的时间 |1 | | | |1-255 | |609 |8 |DG3 |Th_Nr |在封锁后THYRISTOR TRACE的记录号 |7 | | | |2-14 | |610 |2 |DG4 |StatV |在STATUS=REGUL时显示的变量 |N | | | |13种 | |611 |2 |DG5 |Aux1S |对Aux2附加变量编程(来源) |AuxDgn | | | |31种 | |612 |2 |DG6 |Aux2S |对Aux2附加变量编程(来源) |Ean1 | | | |31种 | |613 |2 |DG7 |Aux3S |对Aux2附加变量编程(来源) |Ean2 | | | |31种 | |614 |3 |DG8 |D_Ref |通过Setup Reference设置方波幅值 |10% | | | |0-100% | |616 |5 |DG9 |TimeP |通过Setup Reference设置方波周期 |0.1s | | | |0.1-10s | | | | | | | | | | | | | | | | |DH 模拟量输入偏置 | | | | | | |626 |3 |DH1 |TacOf |测速发电机输入(Tach) |0 | | | |±100% | |628 |3 |DH2 |IfOfs |励磁电流输入(If) |0 | | | |±100% | |630 |3 |DH3 |E1Ofs |可编程模拟量输入(Ean1) |0 | | | |±100% | |632 |3 |DH4 |E2Ofs |可编程模拟量输入(Ean2) |0 | | | |±100% | |634 |3 |DH5 |UdOfs |电枢电压输入(Varm) |0 | | | |±100% | |636 |3 |DH6 |RifOf |差动模拟量输入(Rif) |0 | | | |±100% | | | | | | | | | | | | | | | | |DJ 模拟量输入比例因子 | | | | | | |646 |3 |DJ1 |TachG |测速发电机输入(Tach) |100% | | | |+97~249% | |648 |3 |DJ2 |If_G |励磁电流输入(If) |100% | | | |±249% | |650 |3 |DJ3 |Ean1G |可编程模拟量输入(Ean1) |100% | | | |±249% | |652 |3 |DJ4 |Ean2G |可编程模拟量输入(Ean2) |100% | | | |±249% | |654 |3 |DJ5 |Ud_G |电枢电压输入(Varm) |100% | | | |+97~249% | |656 |3 |DJ6 |Rif_G |差动模拟量输入(Rif) |100% | | | |±249% | |658 |3 |DJ7 |Uvo_G |电源变换器的修正 |100% | | | |0~249% | |660 |3 |DJ8 |Ia_G |电枢电流变换器的修正(CT负载电阻) |100% | | | |+50~+150% | | | | | | | | | | | | | | | | |DK 模拟量输入滤波 | | | | | | |670 |8 |DK1 |TacFl |测速发电机输入(Tach) |0 | | | |0-255 r/s | |671 |8 |DK2 |If_Fl |励磁电流输入(If) |20 | | | |0-255 r/s | |672 |8 |DK3 |Ean1F |可编程模拟量输入(Ean1) |0 | | | |0-255 r/s | |673 |8 |DK4 |Ean2F |可编程模拟量输入(Ean2) |0 | | | |0-255 r/s | |674 |8 |DK5 |Ud_Fl |电枢电压输入(Varm) |0 | | | |0-255 r/s | |675 |8 |DK6 |RifFl |差动模拟量输入(Rif) |0 | | | |0-255 r/s | | | | | | | | | | | | | | | | |DL 模拟量输入绝对值 | | | | | | | | |DLA |TacAb |测速发电机输入(Tach) |OFF | | | |ON/OFF | | | |DLB |IfAbs |励磁电流输入(If) |OFF | | | |ON/OFF | | | |DLC |E1Abs |可编程模拟量输入(Ean1) |OFF | | | |ON/OFF | | | |DLD |E2Abs |可编程模拟量输入(Ean2) |OFF | | | |ON/OFF | | | |DLE |RifAb |差动模拟量输入(Rif) |OFF | | | |ON/OFF | |684 |1 |DL0 |Ai_Bs | | | | | | | | | | | | | | | | | | | | | | |DM 模拟量输出(37-38)(39-41)(40-41) | | | | | | | | |DMA |Pw1Ab |选择PWM1输出形式,ON=绝对值,OFF=实际值 |OFF | | | |ON/OFF | | | |DMB |Pw2Ab |选择PWM2输出形式 |OFF | | | |ON/OFF | | | |DMC |Pw3Ab |选择PWM3输出形式 |OFF | | | |ON/OFF | |694 |1 |DM0 |Pw_Bs | | | | | | | |695 |2 |DM1 |Pw1S1 |选择PWM1输出内容 |Ud | | | |12种 | |696 |2 |DM2 |Pw2S1 |选择PWM2输出内容 |Ifo | | | |12种 | |697 |2 |DM3 |Pw3S1 |选择PWM3输出内容 |N | | | |12种 | |698 |3 |DM4 |Pw1Of |设置PWM1输出偏置 |0 | | | |±100% | |700 |3 |DM5 |Pw2Of |设置PWM2输出偏置 |0 | | | |±100% | |702 |3 |DM6 |Pw3of |设置PWM3输出偏置 |0 | | | |±100% | |704 |3 |DM7 |Pw1_G |设置PWM1输出比例因子 |100% | | | |±200% | |706 |3 |DM8 |Pw2_G |设置PWM2输出比例因子 |-100% | | | |±200% | |708 |3 |DM9 |Pw3_G |设置PWM3输出比例因子 |100% | | | |±200% | | | | | | | | | | | | | | | | |DN数字量输入 | | | | | | | | |DNA |Com1L |COM1(17,22)逻辑方式:ON=低电平有效OFF=高电平有效 |OFF | | | |ON/OFF | | | |DNB |Com2L |COM2(18,22)逻辑方式 |OFF | | | |ON/OFF | | | |DNC |Com3L |COM3(19,22)逻辑方式 |OFF | | | |ON/OFF | | | |DND |Com4L |COM4(扩展X1- 11)逻辑方式 |OFF | | | |ON/OFF | | | |DNE |Com5L |COM5(扩展X1- 12)逻辑方式 |OFF | | | |ON/OFF | | | |DNF |Com6L |COM6(扩展X1- 13)逻辑方式 |OFF | | | |ON/OFF | | | |DNG |Com7L |COM7(扩展X1- 14)逻辑方式 |OFF | | | |ON/OFF | |718 |1 |DN0 |Cm_Bs |DNA~DNG: Bit0~Bit6 | | | | | | |719 |2 |DN1 |Com1S |保留 |OFF | | | |ON/OFF | |720 |2 |DN2 |Com2S |保留 |OFF | | | |ON/OFF | |721 |2 |DN3 |Com3S |输入功能选择,OFF=禁止,Enable=有效,C_Par=参数转换 |OFF | | | |ON/OFF | |722 |2 |DN4 |Com4S |保留 |OFF | | | |ON/OFF | |723 |2 |DN5 |Com5S |保留 |OFF | | | |ON/OFF | |724 |2 |DN6 |Com6S |保留 |OFF | | | |ON/OFF | |725 |2 |DN7 |Com7S |保留 |OFF | | | |ON/OFF | | | | | | | | | | | | | | | | |DO 数字量输出 | | | | | | | | |DOA |Out1L |输出方式:ON=输出低电平有效,OFF=输出高电平有效,OUT1(XM1-24) |OFF | | | |ON/OFF | | | |DOB |Out2L |OUT2(XM1-25) |OFF | | | |ON/OFF | | | |DOC |Out3L |OUT3(扩展X1-1) |OFF | | | |ON/OFF | | | |DOD |Out4L |OUT4(扩展X1- 2) |OFF | | | |ON/OFF | | | |DOE |Out5L |OUT5(扩展X1-3) |OFF | | | |ON/OFF | | | |DOF |Out6L |OUT6(扩展X1-4) |OFF | | | |ON/OFF | |734 |1 |DO0 |Ou_Bs |DOA~DOF:Bit2~Bit7 | | | | | | |735 |2 |DO1 |Out1S |OUT1输出内容选择 |Alarm | | | |14种 | |736 |2 |DO2 |Out2S |OUT2输出内容选择 |Ia_Lim | | | |14种 | |737 |2 |DO3 |Out3S |OUT3输出内容选择 |Bridge | | | |14种 | |738 |2 |DO4 |Out4S |OUT4输出内容选择 |Enable | | | |14种 | |739 |2 |DO5 |Out5S |OUT5输出内容选择 |ErrN=0 | | | |14种 | |740 |2 |DO6 |Out6S |OUT6输出内容选择 |UdFail | | | |14种 | | | | | | | | | | | | | | | | |DP 磁化曲线 | | | | | | |744 |3 |DP1 |M_K1 | |4.8% | | | |0-100% | |746 |3 |DP2 |M_K2 | |9.7% | | | |0-100% | |748 |3 |DP3 |M_K3 | |14.6% | | | |0- 100% | |750 |3 |DP4 |M_K4 | |24.4% | | | |0-100% | |752 |3 |DP5 |M_K5 | |40.0% | | | |0-100% | |754 |3 |DP6 |M_K6 | |70.0% | | | |0-100% | | | | | | | | | | | | | | | | | 增强版软件参数 | | | | | | | | | | |CG 定位调节 | | | | | | | | |CGA |Enable |功能启动 |OFF | | | |ON/OFF | | | |CGB |PosSp |定位完成后脉冲封锁启动 |OFF | | | |ON/OFF | | | |CGC |PosFbk |轴位置显示使能 |OFF | | | |ON/OFF | |430 |1 |CG0 |Ps_Bs | | | | | | | |431 |8 |CG1 |K_Pos |位置给定修正系数 |0 | | | |0-3 | |432 |3 |CG2 |Acc_S |定位速度 |2% | | | |0.1-100% | |434 |6 |CG3 |PrefF |正旋转方向角位置给定 |0 | | | |0-9999 | |436 |6 |CG4 |PrefB |反旋转方向角位置给定 |0 | | | |0- 9999 | |438 |6 |CG5 |P_Err |允许最大的定位误差 |100 | | | |0-9999 | | | | | | | | | | | | | | | | |CH 内部PLC | | | | | | | | |CHA |Enable |功能启动 |OFF | | | |ON/OFF | | | |CHB |Fld_C |磁场接触器控制 |ON | | | |ON/OFF | | | |CHC |H_OpC |封锁状态时断开主电路和磁场接触器 |OFF | | | |ON/OFF | | | |CHD |PwC_CS |监控主电路接触器闭合信号 |ON | | | |ON/OFF | | | |CHE |PIC_CS |监控磁场接触器逼合信号 |OFF | | | |ON/OFF | |442 |1 |CH0 |PI_Bs | | | | | | | |443 |5 |CH1 |ContD |接触器动作与脉冲使能之间的延时 |0.5s | | | |0-20s | | | | | | | | | | | | | | | | |CJ 张力调节器 | | | | | | | | |CJA |T_En |张力闭环调节功能启动 |OFF | | | |ON/OFF | | | |CJB |W_En |张力开卷调节功能启动(卷取) |OFF | | | |ON/OFF | | | |CJC |Taper |Taper功能启动 |OFF | | | |ON/OFF | |450 |1 |CJ0 |Te_Bs | | | | | | | |451 |2 |CJ1 |ToSel |选择张力给定源 |P_CJ4 | | | |4种 | |452 |2 |CJ2 |T_Sel |选择张力反馈源 |Serial | | | |3种 | |453 |2 |CJ3 |ToN0f |使能并选择零速张力给定 |ToN0Of | | | |4种 | |454 |3 |CJ4 |ToRef |张力给定值 |0 | | | |0-100% | |456 |3 |CJ5 |ToN=0 |零速张力给定值 |0 | | | |0-100% | |458 |2 |CJ6 |TapTy |选择Taper功能`函数曲线 |Lin. | | | |Lin./Hyp | |460 |3 |CJ7 |TapDo |Taper功能开始工作时的卷径值 |10% | | | |0.1-99.9 | |462 |3 |CJ8 |Tap_V |当Taper使能且卷径最大时的张力给定值 |50% | | | |0-100% | |464 |5 |CJ9 |TtoNo |张力给定变化斜率时间 |10s | | | |0-25s | | | | | | | | | | | | | | | | |CK 张力反馈调节 | | | | | | | | |CKA |LC_F |张力计位于电机前(ON)/后(OFF) |OFF | | | |ON/OFF | | | |CKB |Terr=0 |张力调节器投入方式(ON=张力差为零时投入) |OFF | | | |ON/OFF | | | |CKC |Gi_Fix |张力调节器积分增益计算方法 |OFF | | | |ON/OFF | |466 |1 |CK0 |LC_Bs | | | | | | | |467 |8 |CK1 |T_K |张力调节器输出值的重新修正 |100 | | | |1-255 | |468 |2 |CK2 |Appl. |选择张力闭环调节器的应用模式 |Nloop | | | |3种 | |470 |3 |CK3 |K_Int |当以速度为函数计算张力调节器的积分增益时,(参数CKC=OFF)重新校正张力调节器 的积分增益 |100% | | | |0-200% | | | | | | | | | | | | | | | | |CL 卷取调节 | | | | | | |474 |2 |CL1 |Type |选择张力开环调节方式(主动/被动) |Axial | | | |Axiial/Tang | |475 |8 |CL2 |W_Flt |卷取调节输出的滤波频率(0=无效) |20 r/s | | | |0-255 r/s | |476 |2 |CL3 |W_Sel |选择卷取运行形式(卷取/开卷) |Wind | | | |Wind/Unwind | |477 |2 |CL4 |Mat_P |选择轧制材料卷绕方式 |Normal | | | |3种 | |478 |3 |CL5 |ToRic |在最大张力且最大卷径时电枢电流期望值重新校正 |100% | | | |0-200% | | | | | | | | | | | | | | | | |CM 惯量补偿 | | | | | | | | |CMA |Enable |惯量补偿功能启动 |OFF | | | |ON/OFF | |480 |1 |CM0 |In_Bs |CMA Enable Bit 0 | | | | | | |481 |2 |CM1 |Type |选择惯量补偿形式 |Const | | | |Const./Var. | |482 |2 |CM2 |DensS |选择材料密度信号源 |P_CM4 | | | |3种 | |483 |2 |CM3 |WdthS |选择材料宽度信号源 |P_CM5 | | | |3种 | |484 |3 |CM4 |Dens. |材料密度 |100% | | | |0.1-100% | |486 |3 |CM5 |Width |材料宽度 |100% | | | |0.1-100% | |488 |4 |CM6 |AccT0 |1st机械加速时间 |0 | | | |0- 999.9s | |490 |4 |CM7 |AccT1 |2nd机械加速时间 |100s | | | |0-999.9s | |492 |4 |CM8 |AccT2 |3rd机械加速时间 |100s | | | |0-999.9s | | | | | | | | | | | | | | | | |CN 卷径计算 | | | | | | |498 |3 |CN1 |D_Min |最小卷径值 |0 | | | |0-100% | |501 |2 |CN2 |FDimS |选择起始卷径源 |P_CN3 | | | |3种 | |502 |3 |CN3 |FDiam |起始卷径值 |0 | | | |0-100% | |504 |3 |CN4 |CDThr |角速度门限值,小于时计算功能无效 |2% | | | |0-10% | |506 |6 |CN5 |WTime |完成整个开卷/卷取所需的卷绕时间 |600s | | | |1-9999s | |508 |2 |CN6 |DiamS |选择实际工作卷径源 |OFF | | | |5种 | | | | | | | | | | | | | | | | |CO 反冲击补偿 | | | | | | | | |COA |Enable |功能启动 |OFF | | | |OF/OFF | |336 |1 |CO0 |BshBs |COA Enable Bit 0 | | | | | | |338 |3 |CO1 |B_Val |设置在反桥后参数CO2设置的时间内的电流限幅值 |1.0% | | | |0.1-100% | |340 |8 |CO2 |Btime |设置在反桥后参数CO1设置的电流限幅值的作用时间(ms) |10 | | | |1-250 | |341 |8 |CO3 |B_Rmp |设置电流限幅值从参数CO1设置值到原限幅值的斜率时间;CO1设置值的起始时间是在C O3的时间设置值结束后(10ms级) |10 | | | |1-250 | | | | | | | | | | | | | | | | |TH 增益调节 | | | | | | | | |TH1 |Gp_K1 |3rd组电机速调的比例增益 |0 | | | |0-9999 | | | |TH2 |Gi_K1 |3rd组电机速调的积分增益 |0 | | | |0-8000 | | | |TH3 |Gd_K1 |3rd组电机速调的微分增益 |0 | | | |0-255 | | | |TH4 |Gp_K2 |4th组电机速调的比例增益 |0 | | | |0-9999 | | | |TH5 |Gi_K2 |4th组电机速调的积分增益 |0 | | | |0-8000 | | | |TH6 |Gd_K2 |4th组电机速调的微分增益 |0 | | | |0-255 | | | |TH7 |TcFGp |采用电压反馈时的速度环比例增益 |0 | | | |0-9999 | | | |TH8 |TcFGi |采用电压反馈时的速度环积分增益 |0 | | | |0-8000 | | | | | | | | | | | | | | | | |TJ 定位调节 | | | | | | | | |TJ1 |GpPos |电机轴位置调节器的比例增益 |0 | | | |0-9999 | | | |TJ2 |Gp_P1 |定位完成后电机速调的比例增益 |400 | | | |0-9999 | | | |TJ3 |Gi_P1 |定位完成后电机速调的积分增益 |80 | | | |0-8000 | | | |TJ4 |Gd_P1 |定位完成后电机速调的微分增益 |0 | | | |0-255 | | | |TJ5 |Gp_P2 |保留 |400 | | | |0-9999 | | | |TJ6 |Gi_P2 |保留 |80 | | | |0-8000 | | | |TJ7 |Gd_P2 |保留 |0 | | | |0-255 | | | | | | | | | | | | | | | | |TK 张力闭环调节 | | | | | | | | |TK1 |Gp_T |张力调节器的比例增益 |100 | | | |0- 9999 | | | |TK2 |Gi_T |张力调节器的积分增益 |100 | | | |0-8000 | | | |TK3 |LimAT |张力调节器输出正向限幅 |2% | | | |0-100% | | | |TK4 |LimIT |张力调节器输出反向限幅 |-2% | | | |-100%-0 | | | |TK5 |NoLmT |张力调节器输出作为速度给定补偿后的正向速度限幅(COM3=ON使能) |+100% | | | |0-+100% | | | |TK6 |NoLmB |张力调节器输出作为速度给定补偿后的反向速度限幅(COM3=ON使能) |-100% | | | |-100%-0 | | | |TK7 |Gd_T |张力调节器的微分增益 |0 | | | |0-255 | | | | | | | | | | | | | | | | | | | | | | | | 数据类型: 1:0-7位对应参数的ON/OFF。 2:矛盾位类型,值在0到N-1范围内变化,N为可被列举的数。 3:带符号的字,CCCCH~3333H(-1000‰~1000‰)?? 4:时间范围下端,360.0写成3600 (E10H) 5:时间范围的下端字节,15.6写成156 (9CH) 6:无符号的字,如一个范围下端为9999,(270FH) 7:无符号的字,10进制,如999,9为270FH 8:单字节0-255
更多简介内容

推荐帖子

评论

登录/注册

意见反馈

求资源

回顶部

About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版 版权声明

北京市海淀区知春路23号集成电路设计园量子银座1305 电话:(010)82350740 邮编:100191

电子工程世界版权所有 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2021 EEWORLD.com.cn, Inc. All rights reserved
$(function(){ var appid = $(".select li a").data("channel"); $(".select li a").click(function(){ var appid = $(this).data("channel"); $('.select dt').html($(this).html()); $('#channel').val(appid); }) })
×